What Should I Use To Clean And Treat A Rubber Bandsaw Tire
Bandsaw Tire Cleaner
Forum for Maintenance and Repair topics. Feel complimentary to ask questions or contribute.
Moderator: admin
- Lodgepole
- Golden Member
- Posts: 264
- Joined: Tue Oct 17, 2006 seven:21 pm
- Location: Idaho
Bandsaw Tire Cleaner
I just finished attending a form taught by David Marks. He recommended attaching a brush to the inside of the bandsaw case to clean off the lower tire.
I have too seen various woodworking tips where the handle of a used toothbrush is heated to curve at a 90 degree bending. The toothbrush was then bolted to the case of the bandsaw. The bristles of the toothbrush are then in contact with the bandsaw tire.
Has anyone done this to their Shopsmith Bandsaw?
-
JPG
- Platinum Fellow member
- Posts: 33102
- Joined: Wednesday Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (WILDCAT territory)
lodgepole wrote:I just finished attending a class taught by David Marks. He recommended attaching a brush to the within of the bandsaw instance to clean off the lower tire.
I have besides seen various woodworking tips where the handle of a used toothbrush is heated to bend at a ninety degree bending. The toothbrush was then bolted to the case of the bandsaw. The bristles of the toothbrush are then in contact with the bandsaw tire.
Has anyone done this to their Shopsmith Bandsaw?
NOT I, but have been thinking of doing something to 'brush' the tires. A toothbrush seems a good idea to me!:)
╔═══╗ Goldie(Bought New SN 377425)/4" jointer/half-dozen" beltsander/12" planer/stripsander/bandsaw/powerstation /Ringlet saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ x
╟JPG ╢
╚═══╝
- foxtrapper
- Golden Member
- Posts: 439
- Joined: Fri Feb 16, 2007 10:05 am
Aye. I've an erstwhile toothbrush mounted within mine running against the lower tire. Works well. Drilled a small hole in the frame to mount on. Cut the toothbrush short and drilled a pigsty in information technology too. Simple screw and nut to mount.
The difference in noise is remarkable with a clean wheel.
-
JPG - Platinum Member
- Posts: 33102
- Joined: Midweek Dec ten, 2008 7:42 pm
- Location: Lexington, Ky (Wildcat territory)
foxtrapper wrote:Yes. I've an old toothbrush mounted inside mine running confronting the lower tire. Works well. Drilled a pocket-size pigsty in the frame to mount on. Cut the toothbrush brusque and drilled a pigsty in it besides. Simple screw and nut to mount.
The difference in noise is remarkable with a clean bicycle.
Where did you position it? Does information technology 'castor' the blade as well?:)
╔═══╗ Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman x" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Marker VII restoration in 'progress'/ x
╟JPG ╢
╚═══╝
- markap
- Golden Member
- Posts: 99
- Joined: Midweek Oct fifteen, 2008 one:44 pm
- Location: Reston, VA
foxtrapper wrote:Yes. I've an old toothbrush mounted inside mine running against the lower tire. Works well. Drilled a small hole in the frame to mount on. Cutting the toothbrush short and drilled a hole in it as well. Unproblematic screw and nut to mount.
The departure in noise is remarkable with a clean wheel.
Picture please??
SS MV 520, bandsaw, jointer, planer, belt sander, mortise unit, biscut jointer, speed reducer, tool residuum upgrade, sliding cantankerous cut table, DC3300
-
robinson46176
- Platinum Member
- Posts: 4178
- Joined: Mon Mar 09, 2009 9:00 pm
- Location: Central Indiana (Shelbyville)
The bandsaw sawmill I used to own some years ago came with a small wire cycle (about three") mounted in front of the drive wheel. It ran at an bending and barely brushed the bract as it passed nether the brush which cleaned the bract surface just earlier it contacted the drive bicycle. Of form the sawmill ran horizontally and it also didn't have tires on the wheels. The wheels were steel and flat with a step cut that helped guide the back of the blade.
I wouldn't want to run a wire cycle against the rubber tire simply a picayune bristle wheel running at an angle with very light contact might do a nice task.
-
My new bandsaw sawmill uses an all together different setup and doe not have a brush.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), iv Poly vee ane ane/8th HP Mark V's, Marker VII, 1 Mark V Mini, one Frankensmith, one 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, i" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
- charlese
- Platinum Member
- Posts: 7501
- Joined: Fri Dec 08, 2006 10:46 pm
- Location: Lancaster, CA
Rubber Tire Maintenance Tip
I'll post this Tip once more:
If yous accept prophylactic tires on your bandsaw, all you need to continue larger amounts of sawdust from sticking to the wheels is to wet a rag with Silicone from a spry can and wipe downward the tires. I've done this for the past 5 years following 5 years of letting a ane/4" blade under tension in the saw. At that time, there was a groove being pressed into the rubber and the rubber was hardening and cracking on the surface.
Afterward v years of semi regular cleaning with Silicone, near of the cracks have dissappeared then has most of the i/iv" blade dent. Now upon cleaning the insides, I find some sawdust on the tires, only certainly non the amounts I had earlier. The surface of the tires are now simply every bit soft equally when new.
Sometimes, when the bract has been removed, I've even been known to squirt the silicone directly onto the tires, then wipe it off. I've yet to find any "fisheye" or other effect of the Silicone apply. However I don't get sloppy with information technology.
Octogenarian's have an earned correct to be a curmudgeon.
Chuck in Lancaster, CA
-
ryanbp01
- Platinum Fellow member
- Posts: 1480
- Joined: Mon Jun 25, 2007 4:43 pm
- Location: Monroeville, IN
My Craftsman bandsaw came with a brush already attached to clean the wheel and the bract.
BPR
-
thainglo
- Gold Member
- Posts: 81
- Joined: Mon May 19, 2008 10:28 pm
- Location: Silvery Creek, GA
charlese wrote:I'll mail service this Tip again:
If you have rubber tires on your bandsaw, all you need to keep larger amounts of sawdust from sticking to the wheels is to wet a rag with Silicone from a spry tin can and wipe down the tires. I've done this for the past v years following 5 years of letting a 1/4" blade under tension in the saw. At that time, there was a groove being pressed into the rubber and the rubber was hardening and slap-up on the surface.
Afterward 5 years of semi regular cleaning with Silicone, most of the cracks have dissappeared and and then has most of the ane/four" blade paring. Now upon cleaning the insides, I detect some sawdust on the tires, but certainly not the amounts I had earlier. The surface of the tires are now simply every bit soft every bit when new.
Sometimes, when the bract has been removed, I've fifty-fifty been known to squirt the silicone straight onto the tires, then wipe it off. I've yet to observe any "fisheye" or other upshot of the Silicone utilize. However I don't get sloppy with it.
Charlese - delight analyze on the Silicone yous used. Is it WD40? I've got a couple of wheels with the rubber dried and cracked pretty bad ---
[Attach]3829[/Attach]
Would like to bring life back into them and use your advise on the production you recommend.
Thanks!
Matt
- Attachments
-
-
- 82 Shopsmith Bandsaw Wheel 2.jpg (70.64 KiB) Viewed 14565 times
-
Lost count, over a dozen rebuilt/repaired/restored
Personal equipment: 510 made in 1993, chugalug sander, jig saw, ring saw, planer and jointer
Matt in GA
-
beeg
- Platinum Member
- Posts: 4735
- Joined: Sun Oct xiv, 2007 ii:33 pm
- Location: St. Louis, Mo.
I think information technology's time to REPLACE them. 
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 foursquare foot shop.
.
.
Bob
Source: https://forum.shopsmith.com/viewtopic.php?t=3304
Posted by: bauderhartatied.blogspot.com
0 Response to "What Should I Use To Clean And Treat A Rubber Bandsaw Tire"
Post a Comment